Noticias y eventos

Explicación de la tabla de cargas de las grúas: por qué la capacidad nominal no es la respuesta

On 16 November 2026, Crane & Transport Briefing published a technical article with a deceptively simple question in its title: why does crane capacity alone not confirm a safe and workable lift? The author, Konstantin Kalnyi — founder and CEO of shipbroker Kiev Shipping and a 25-year project-cargo specialist — makes a point that matters to every crane buyer, not just to those chartering vessels: the tonnage printed beside a crane’s name is the beginning of an assessment, never its conclusion. What decides the lift is the crane load chart read at the real working radius, with every item in the lifting train accounted for. This guide turns that argument into a practical technical check: how a load chart works, how a load moment indicator (LMI) uses it as a live limit, and what to verify before you specify, buy or troubleshoot one.

Disclosure of interest: This article is published by the editorial desk of SeeZol (Yichang, China; szlmi.com), a manufacturer of load moment indicators, safe load indicators and onboard weighing systems. We sell devices in the category discussed below, so read the purchasing sections as a buyer’s guide from a vendor, not as an independent audit. We make no claims about competitors and we state the limits of these devices explicitly. No test result, accuracy figure or capacity value in this article is presented as verified data from our own products — where a number appears, its source is named. Nothing here is a substitute for the crane manufacturer’s own chart, manual or a competent lift plan.

The Crane Load Chart vs. the Number on the Brochure

Kalnyi’s article opens with a scenario familiar to anyone who has read a crane datasheet: a vessel description lists cranes of 80, 120 or 250 tonnes, and the immediate assumption is that any load below that figure can be lifted. In practice, he writes, “the number stated beside the crane is not a final confirmation of lifting capability. It is only the starting point for a much wider technical and operational assessment.”

The same misread happens on construction sites every day. A 250-tonne all-terrain crane is not a 250-tonne crane at every radius, in every configuration, with every boom length. The brochure figure is usually the maximum capacity at the most favourable configuration — short boom, small radius, fully extended outriggers. Move the load out, extend the boom, or lift over the side rather than over the rear, and the permissible load falls, sometimes steeply. The document that tells you how far it falls is the crane load chart, and it is machine-specific.

Mobile crane boom extended at radius — capacity changes with configuration
Boom length, radius and operating configuration all change the permissible load. Photo: AlfvanBeem / Wikimedia Commons (CC0).

How a Crane Load Chart Actually Works

A load chart is a grid. Along one axis you find the working radius — the horizontal distance from the crane’s rotation centre to the load hook. Along the other you find a configuration: boom length or extension, jib fitted or not, counterweight, and outrigger state. Each cell gives the gross load the machine may handle at that combination. Read the chart at the wrong radius or the wrong configuration and you get a number that is either needlessly conservative or dangerously optimistic.

Three habits prevent most reading errors:

  1. Use the chart for the exact machine. Charts are model- and sometimes serial-number-specific. A chart from a similar crane is not interchangeable.
  2. Read the configuration column, not just the radius row. Outriggers fully extended versus partially extended can change the permitted load substantially; the chart states which line applies.
  3. Add everything below the hook. Kalnyi’s example is blunt: a 95-tonne cargo item is not a 95-tonne crane load if 10 tonnes of lifting beams, spreaders, slings and shackles are needed. The chart is loaded against the gross figure.
What the chart assumes vs. what the site must supply
The crane load chart tells youThe chart cannot tell you
Permissible gross load at a given radius and configurationWhether the ground under the outriggers can carry the reaction forces
Which boom / jib / counterweight combination the figure belongs toThe true centre of gravity of an oddly shaped load
The limits of the machine’s own structure and stabilityThe weight of rigging, spreaders and below-hook devices you add
Where the cut-out should act for that configurationWind, swell, visibility and the sequence of a tandem lift

How a Load Moment Indicator Turns the Chart into a Live Limit

Here is the bridge between the article’s argument and the device in your cab. A load moment indicator does not “know” how strong the crane is in the abstract. It stores the manufacturer’s load chart as data, measures the inputs that select a point on that chart — mainly radius or boom angle, boom extension, and a load signal from a pressure sensor, load pin or similar — and continuously compares the resulting moment or load against the chart value at that exact configuration. When the measured value approaches the permitted one, it warns; at the set limit it inhibits the dangerous motion. In other words, it automates the discipline Kalnyi is asking for: read the chart at the actual radius, every second, including while the boom is moving.

That is also why the underlying chart matters more than the display. A limiter with a crisp screen but the wrong chart, a partial chart, or a chart that does not cover your jib and counterweight combination is a limiter that will give a confident answer to the wrong question. Our explanation of LMI working principles and our deeper dive into composition and applications walk through the signal chain in detail.

Tower crane — load moment indicator applies this machine's own load chart
A tower crane: the limiter applies this machine’s own chart, not a generic one. File photo: Dmitry Ivanov / Wikimedia Commons (CC BY-SA 4.0).

Where the Load Signal Comes From

The load input is the part most often misunderstood in a purchase conversation. There is no single universal method, and the right one depends on the machine:

  • Hydraulic pressure sensing infers hook load from cylinder pressure. It is non-invasive to fit but sensitive to friction, temperature and circuit behaviour, so calibration matters. SeeZol’s oil-pressure sensor installation guide covers the fitting details.
  • Load pins and weighing sensors measure force directly at a pin, sheave or rope anchor. They are common in retrofits where drilling the hydraulic circuit is undesirable. Our sensor selection guide y el wider sensor comparison set out the trade-offs.
  • Sistemas de pesaje a bordo serve a related but distinct goal: recording how much was lifted, for billing, fleet control or material accounting, rather than only preventing overload. The two functions can share sensors but answer different questions.

Wheeled excavator — hydraulic pressure and weighing pins as load-signal sources
Load signals are machine-specific: on excavators and loaders, as on cranes, the input may come from hydraulics or weighing points. File photo: Wikimedia Commons (see credits).

Six Checks Before You Buy a Limiter

Turn the load-chart logic into a purchase checklist. These are the questions we would ask any supplier, including ourselves:

  1. Is your exact crane and configuration covered? Ask for the chart list, not a general compatibility claim. Check jib, counterweight and outrigger states you actually use.
  2. Which sensing path is proposed, and why? Pressure, load pin or another method — and what does the installer need to do to the machine?
  3. How does the system treat rigging weight? Does it let you enter below-hook weight, and does the alarm point include it? Kalnyi’s 95 t + 10 t example is the test case.
  4. What exactly happens at the limit? Warning only, or motion cut-out? Which motions, and can an authorised operator override under defined conditions?
  5. What records does it keep? Timestamped events, configuration at the moment of alarm, and a way to export them. This is the recording question now being discussed in the standards community — see our note on the move from single-chip electronics to IoT edge computing.
  6. Who signs the calibration, and on what reference? Ask for the procedure and the record, not an assurance that it “comes calibrated”. Our guide on choosing an LMI for your machine expands this list.
Rubber-tyred gantry crane — check the exact configuration your chart covers
Gantry-class machines make the same point: chart coverage must match the configuration you actually operate. File photo: Wikimedia Commons / Only Truth (CC BY-SA 3.0).

Troubleshooting: When the Reading Drifts

Kalnyi warns that estimated or incorrect cargo information can undermine an entire operation. The same is true of a limiter fed by a drifting sensor. A reading that is off by a small percentage at low load can be the difference between a controlled stop and a cut-out in the middle of a slew. Before blaming the electronics, work through the mechanical and setup causes in order:

  1. Zero / dead-load reference. Was the system zeroed with the hook and below-hook gear in the state you actually use? A wrong reference biases every reading.
  2. Span against a known load. Has a certified test load been applied and entered, with the reading allowed to settle?
  3. Binding and mechanical rub. A load path that touches structure gives repeatability problems that no electrical adjustment will fix.
  4. Cable and connection condition. Damaged cables, wet junctions and loose terminals are a common source of wandering readings.
  5. Radius and angle input. If the system picks the wrong chart column because the angle or length signal is wrong, the load signal may be perfect and the decision still wrong.
  6. Documentation. Record date, test weights, certificate numbers, readings and who did the work — the record is what shows a slow drift before it becomes an incident.

Our field guide to five common calibration pitfalls behind inaccurate LMI readings goes deeper on each cause, and our notes on full-environment protection explain why temperature and moisture change readings in outdoor fleets.

Lattice-boom crawler crane — radius and boom-length inputs select the chart column
On lattice-boom machines, a wrong radius or boom-length signal selects the wrong chart column before the load signal is even considered. File photo: Wikimedia Commons (see credits).

What the Chart and the Limiter Cannot Do

This is the boundary we are most careful to state. A load chart is information; a limiter is a device that enforces part of that information. Neither replaces the judgement calls in Kalnyi’s list:

  • They do not weigh the rigging for you. If lifting beams, spreaders or slings are added below the hook, that weight must be entered or measured. A limiter reading only the hook load will understate the true crane load — exactly the 95 t + 10 t trap.
  • They do not verify the centre of gravity. The article notes that a load whose real centre of gravity differs from the drawing may tilt after lifting. No chart value fixes a bad lifting plan.
  • They do not check ground bearing, outrigger mats or deck strength. The chart assumes the machine is supported. The site has to prove it.
  • They do not coordinate a tandem lift. Two limiters on two cranes do not manage load share, slewing sequence or communication between operators.
  • They do not read the weather. Wind on a large surface area can make a light load unsafe; the chart’s tonnage does not see it.

A useful way to frame this for buyers: the limiter protects the machine’s own limit envelope; the lift plan protects everything the machine cannot see. If you want a broader comparison of device classes, our article on LMI, SLI, RCI and RCL sets out what each device does and does not cover, and our page on crane safe load limiters shows the product family in context.

FAQ: Crane Load Charts and Limiters

Is a higher-capacity crane always safer for the same load?
Not automatically. Safety depends on the load at the required radius and configuration. A larger crane working at a long radius can be closer to its chart limit than a smaller one working close in. Read both charts at the actual radius.
Does an LMI replace the load chart?
No. The limiter stores and applies the chart; the operator still needs the chart and the manufacturer’s manual for planning, and a lift plan for anything non-routine.
Can I use one chart for several cranes of the same model?
Only if the manufacturer states the chart applies to those serial numbers and configurations. Charts can differ with counterweight, boom and jib options.
Why does my limiter read correctly at low radius but drift when extended?
Common causes are radius or boom-length signals, sensor zero and span, and mechanical effects such as binding. Check the inputs that select the chart column, not only the load signal.
What should a calibration record contain?
Date, test weights and their certificate numbers, readings at each point, environmental conditions where relevant, the person who performed the work, and the next due date.

Talk to a specialist: if you need the load chart coverage checked against your actual crane configuration, send us the make, model, serial number and the options fitted. We will tell you what our system supports and, just as importantly, where it does not.

Contactar con soporte técnico

Rellene el siguiente formulario y en breve nos pondremos en contacto con usted.